DO NOT TRY THIS AT HOME : Our text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(48 votes) Published: Aug 07, 2008 10:36 a.m. Viewed 285 times
i am truly sorry i had pictures but could not get them on and i will do my best to be as graphic in the explenation
ok this taxes alot of resources alot of time alot of brain power but i THINK it would be effective and i HAVE NOT DONE IT YET partly because i dont have the parts yet i THINK it would be effective because you can grab a car battery and it will shock you just not horribly BUT if you grap an uncoverd spark plug wire IT WILL LIGHT YOUR ASS UP !!! you get lit up because of the HEI i was talking about on most newer cars there is a small box/ canister that is between the distrubuter and battery it is called a
HIGH ENERGY IGNITION SYSTEM it is what give the tazer its power
to build it you need
1 -to find the HEI coil it can only be found on NEWER cars only usually ones that are fuel injected it is fuel injected if theres not a big box on the engine the HEI coil is ALWAYS located btwen the distributer and the battery to find the distrbuter find a spark plug folow the wire to a little rond canister tha the wire goes into there will be a wire right in the middle folow that one to the HEI coil remove it and save it for later
2 a GIANT flash light battery like one that goes into a the BIG flashe lights you can get them at caseys general store usually
3 some sort of switch you need two of them like one off of a grill
4 some thing to mount it all on
5 electrical tape ( you dont wana get shocked !!)
6 copper wire
7 paper clips or some VERY heavy steel wire
ok after you get the HEI take what ever your going to mount it on and take hot glue or tape what ever and put it on the fronter part of the board or what ever
you need then you take your bigole battery and tpe it behind it take your copper wire and wrap it in the electrical tape and wrap the wire except about on the last inch on the ends and you need to do this two or three times and run it from the battery to the COIL and hook them both up to thte batery and take your heavt wire and bend it so it look like an L wrap where your going to mount them on the thing in elctrcal tape the hot glue them on be VERY GENORUS ON THE GLUE you dont want them to come off when you jap some one you then take the two grill switches and pu them in the middile of the wires that your running to the to the heavy metal wires you use two so you have a saftey
and your done depending on the battery you may get 40,000 to 75,000 volts
ORRRR if you want the traditanl 150,000 volts of a car plu take four or five jumper cable and tape black to black with elctrical tape and tape red to red with elctrical tape and hook it to the battery and figure out some way to keep the cable hooked to the batter and to hook them up you just have to tape the copper wires to the end of the jumper cables
the down fall of this design is that it has limited rang but you can keep it in your car or something but the other one is fairly portable
Aug 07, 2008 10:54 am - Maybe its just because I’m not a mechanic but I really don’t understand most of what you’re saying here.
Pictures would definitely help here (I realize you said you couldn’t get them on here but you should try to figure out why). Its also hard to read because of the improper grammar and the fact that I can’t tell where one thought ends and another begins.
Add pictures and rewrite this better in a new egg and that’ll probably get five stars.
As of right now I’m holding my vote.
Aug 07, 2008 12:53 pm - i went out and took pic on my dads truck but they wouldnt up load or nothing and i was pissed cuz ithouhgt they had loaded and they hadnt so yeh
ok this taxes alot of resources alot of time alot of brain power but i THINK it would be effective and i HAVE NOT DONE IT YET partly because i dont have the parts
Aug 07, 2008 1:42 pm - Upload them to Photobucket or Putfile.com, or some other pic. hosting sevice.
Then it when you upload them it should give you a link. Copy that link.
Now wherever you want the pic to appear, add this
[img]the link you copied earlier goes here[/img ]
Aug 07, 2008 4:25 pm - TTTTTTTTTTTHHHHHHHHHHHHHH HHHHHHHHHHHAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAANK YOU you dont know how long ive been trying to figure that shiat out THANK YOU
Aug 07, 2008 4:38 pm - 0*’s "Tazer" A Tazer?? You Can Just Buy One Online And There’s Better Guides Then This On The Internet With Pictures And Video,0*’s For Your Profile As Well
Aug 07, 2008 9:22 pm - Learn tags here... Practice tags here. Type the tag you want to try, and click ’Preview’. It’ll show you how it will show up. (That way you don’t get labeled ’Postwhore’.. ) If you still have questions, message me...
A g 11, 2008 7:10 pm - YET AGAIN i am mciain with a new acount telling you this so i can tell hooded alchemist to GO FUCK HIM SELF AGAIN GO DIE YOU DICK HOLE
Edit Page
Message mciain
Add Comment
Add to Favorites
Email to Friend
